Мы становимся CPG Europe.
Explore our brands
Вернуться к поиску
Паркетный клей

Супер-клей для всех типов деревянных поверхностей. Купить клей для дерева TREMCO у официального представителя tremco illbruck в России по телефону в Москве (495) 644 02 99.

Эластичный супер-клей для всех типов деревянных поверхностей: деревянные плиты, деревянные мозаичные полы, ламинированные полы, плиты из массива дерева, дощатый пол. используется на всех типовых напольных основах: семь из песка, бетона, камень, металл, древесина, эпоксидные мембраны.

Бочка 10л (17кг)

  • не содержит растворитель и воду
  • отверждение 2 часа
  • совместим со всеми типами напольного отопления

All phases of installation should comply with BS 8201, BS 8203, CP 102 and /or other local installation standards and codes of practice.


  • Ensure the subfloor is flat, clean, sound and dry and free from contaminants that may hinder adhesion, this includes, paint, varnish, polish, old adhesive residues and plaster spots.
  • Existing wooden subfloors must have an intact base DPM.
  • The subfloor should be tested in accordance with British Standards, using a properly calibrated and
    insulated hygrometer.
  • A reading of 75% RH or less confirms that the subfloor is satisfactorily dry. Where this has not been attained, it is necessary to apply a TREMCO surface membrane to suppress residual moisture. For further information contact Technical Services.
  • Ensure the timber is acclimatised in accordance to the manufacturer’s instructions in the environment in which it is to be laid.
  • Always allow an expansion gap around any perimeters or columns to allow for natural movement of the wood when bonded.


  • Mechanically remove all surface treatments on concrete bases.
  • Repair any deep indentations in the subfloor with TREMCO SX400 Cementitious Repair Mortar.
  • Lightly abrade calcium sulphate to remove any surface laitance. Always prime before applying a suitable TREMCO smoothing compound to calcium sulphate screeds.
  • Apply a suitable TREMCO smoothing compound at a minimum thickness of 3 mm.
  • See relevant technical data sheet for full information.


  • Not recommended for use over existing floor coverings.


Ensure substrate is suitable for the adhesive before application. Very porous substrates can be primed with CS150 Acrylic Primer. Contact tremco illbruck Customer Services for details.


  • On a smooth floor spread evenly over the floor surface with a triangular notched trowel cut 3 mm deep x 6 mm.
  • For rough textured floors a deeper notched trowel may be required. This will adversely affect the coverage rate of the adhesive.
  • Spread the adhesive with a sweeping motion at a 60° angle and place the wood into the adhesive while it is still wet.
  • Press firmly or gently tap the wood into the adhesive to ensure good overall contact. Where necessary use heavy objects to hold the wood firmly in place during curing time.
  • The bonded wood will be suitable to take foot traffic 6 to 8 hours after application. It should be left for 48 hours before sanding or varnishing takes place.

For full application information, refer to product data sheet or contact tremco illbruck customer services on 01942 251400


Техническая информация

CompositionSF520 Flexible Wood Adhesive is formulated
from advanced polymer technology
Open Time/Workability
(at +20°C)
Approximately 20 minutes
Specific Gravity1.07
Application Temperature Range+4°C to +30°C
Service Temperature-20°C to +60°C
CoverageUsing a B3 or a 3 mm x 6 mm ‘V’ or a notched
trowel the coverage is approx. 0.8 - 1.1 kg/m²
StorageStore in dry conditions between +5°C and +25°C
Shelf Life12 months from manufacturing date, when stored as recommended in original unopened containers
    Узнайте цену и наличие товара прямо сейчас

    Поиск продукта

    Область применения